Rank: Newbie
Groups: Registered
Joined: 5/27/2020(UTC)
Posts: 5
Location: Northern California
|
I have a simple 2 camera setup. A camera has a text/grahpic overlay, I want to cut to the B camera clean with no overlay. How is that possible? I don't want to do it in two steps, fade off the graphic and then cut. This should be straight forward in basic production.
The reverse is true: how to I cut to a camera with a text/graphic overlay, when I use the Cut, the graphic fades on. Is that because there's a time embedded in the overlay channel that forces a fade whenever it's used?
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 3/20/2014(UTC) Posts: 2,721   Location: Bordeaux, France Thanks: 243 times
Was thanked: 794 time(s) in 589 post(s)
|
Check how to use "triggers" in the manual and on vMix YouTube channel
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 2/9/2013(UTC)
Posts: 259
Location: Katy, Texas
Was thanked: 37 time(s) in 37 post(s)
|
If the overlay always appears on Camera A, you can use the multiview for Camera A to add the overlay.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 12/27/2012(UTC) Posts: 5,098  Location: Belgium Thanks: 285 times
Was thanked: 922 time(s) in 761 post(s)
|
Also several shortcuts can br combined under same key.
|
|
|
|
|
|
Rank: Newbie
Groups: Registered
Joined: 5/27/2020(UTC)
Posts: 5
Location: Northern California
|
Thanks for the reply.
I'm in the middle of trying that good idea. Where to set to trigger; in Settings or in multi-view or in the input. There are many place to check. So the idea is to cut to the multi view instead of the camera. But I might loose a fade to get it on. I'm still playing with getting this idea on.
Mike
|
|
|
|
|
|
Rank: Newbie
Groups: Registered
Joined: 5/27/2020(UTC)
Posts: 5
Location: Northern California
|
Making a multiview is straight forward. I can cut in and out of the multiview. Making a trigger little more challenge.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 4/6/2019(UTC) Posts: 95  Location: Florida Thanks: 10 times
Was thanked: 13 time(s) in 11 post(s)
|
 vmix cut.JPG (345kb) downloaded 9 time(s).Reference the picture attached... On the overlay's triggers, set up "OnOverlayIn" and "OnOverlayOut" to jump between your two cameras. then setup a shortcut to turn on or off the overlay and that is one way do your overlay induced transition
|
|
|
|
|
|
Rank: Newbie
Groups: Registered
Joined: 5/28/2020(UTC)
Posts: 1
Location: Brasil
|
how do I enable two capture cards simultaneously? I have two Avermedia LGPL, one for each camera. In vmix I can only enable one card or another. never both at the same time
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 12/27/2012(UTC) Posts: 5,098 Location: Belgium Thanks: 285 times
Was thanked: 922 time(s) in 761 post(s)
|
Originally Posted by: Jonlima22  how do I enable two capture cards simultaneously? I have two Avermedia LGPL, one for each camera. In vmix I can only enable one card or another. never both at the same time Hmm so you are not able to have your 2 cameras as input at the same time but asking this in a post regarding a cut between 2 cameras ? May i suggest asking this in a new post in the hardware section , you will have a better chance of getting a response (as now its buried in another topic )
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
Important Information:
The vMix Forums uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
