Rank: Advanced Member
Groups: Registered
Joined: 2/15/2018(UTC)
Posts: 44
Location: Spain
|
I just bought the Tascam Model 12 sound console. I have installed the software, driver and firmware updater.
I have added all the audio channels of the Tascam to VMIX and it has recognized them independently, this is what I needed but the problem is that if I raise the fader of input 1 of the Tascam it does not increase the volume on audio input 1 of VMIX.
The gain knob for each channel does work correctly, when I turn it up on the Tascam it raises the volume level on the VMIX.
If I press the Mute key on channel 1 on the Tascam, the sound on channel 1 on VMIX is not cut.
Is there a way that if I raise the fader on the Tascam, it will also raise the volume level in VMIX?
Thank you.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 2/23/2019(UTC)
Posts: 556
Thanks: 62 times
Was thanked: 130 time(s) in 118 post(s)
|
According to the manual at https://www.tascam.eu/en...Model12_OM_EFS_RevF.pdf, "Selecting the positions that recording signals are sent from each channel", you can set the USB send point to Pre Compressor, Post Compressor or Post EQ. For what you want to do, you would need to set it to Post Fader, but the mixer doesn't support it.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 2/15/2018(UTC)
Posts: 44
Location: Spain
|
In the manual I have seen the following:
******
AUX2/FX knobs (1-6, 7/8-9/10)
Use to adjust the levels of the signals sent to the AUX2/FX bus (POST FADER)
******
POST FADER
The signal is sent to the AUX 1 bus after adjustment by the channel fader.
******
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 2/23/2019(UTC)
Posts: 556
Thanks: 62 times
Was thanked: 130 time(s) in 118 post(s)
|
AUX usually refers to the analog outputs of the mixer. If you want to use the faders and have an effect in vMix, you would probably have to use the Master output via USB in vMix (select Input 11&12 in vMix). Or maybe write to Tascam support, and ask if it is possible to set the USB send point to "Post Fader".
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 7/4/2021(UTC) Posts: 310  Thanks: 8 times
Was thanked: 40 time(s) in 35 post(s)
|
I'm not aware of any mixer that provides individual audio inputs without ASIO, nor am I aware of any mixer that uses ASIO for that post-fader.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 2/23/2019(UTC)
Posts: 556
Thanks: 62 times
Was thanked: 130 time(s) in 118 post(s)
|
Originally Posted by: WaltG12  nor am I aware of any mixer that uses ASIO for that post-fader. FWIW, the Behringer XR18 allows to set it to post fader (or any other stage of the chain) for each audio input.
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
Important Information:
The vMix Forums uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
