Rank: Advanced Member
Groups: Registered
Joined: 2/20/2019(UTC) Posts: 63  Location: Firenze Was thanked: 5 time(s) in 5 post(s)
|
Hello,
i've been using Behring audio USB interfaces like UMC1820 where you can have every single channel available separetely in vMix using ASIO for all drivers, as well sending audio busses to output channels.
Something similar is happening on Yamaha 01V.
I'm wondering if the Behringer Xenyx family behaves the same way or you just send the main mix on the USB interface, and also if you can get any channel from the computer to the mixer.
Anyone using those units ?
Anyone using Allen & Heat ?
thanks your your messages
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 12/24/2021(UTC) Posts: 496  Location: athens Thanks: 121 times
Was thanked: 70 time(s) in 66 post(s)
|
Originally Posted by: fabfab10  Hello,
i've been using Behring audio USB interfaces like UMC1820 where you can have every single channel available separetely in vMix using ASIO for all drivers, as well sending audio busses to output channels.
Something similar is happening on Yamaha 01V.
I'm wondering if the Behringer Xenyx family behaves the same way or you just send the main mix on the USB interface, and also if you can get any channel from the computer to the mixer.
Anyone using those units ?
Anyone using Allen & Heat ?
thanks your your messages Hello. I dont have an answer in your question but i want to ask something for UMC1820 if possible to be done. Let`s say we have 5 microphones and we want the direct audio of these microphones to be sent as audio out from one of the back line outs or headphones A or B? is it possible to be done? thank you
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 7/1/2020(UTC) Posts: 88  Location: Earth Was thanked: 18 time(s) in 16 post(s)
|
The Xenyx series only have 2x2 USB AFAIK. If you are looking for every channel over USB look to the XR18 or the X32 series.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 2/20/2019(UTC) Posts: 63 Location: Firenze Was thanked: 5 time(s) in 5 post(s)
|
Originally Posted by: nikosman88 Originally Posted by: fabfab10 Hello,
i've been using Behring audio USB interfaces like UMC1820 where you can have every single channel available separetely in vMix using ASIO for all drivers, as well sending audio busses to output channels.
Something similar is happening on Yamaha 01V.
I'm wondering if the Behringer Xenyx family behaves the same way or you just send the main mix on the USB interface, and also if you can get any channel from the computer to the mixer.
Anyone using those units ?
Anyone using Allen & Heat ?
thanks your your messages Hello. I dont have an answer in your question but i want to ask something for UMC1820 if possible to be done. Let`s say we have 5 microphones and we want the direct audio of these microphones to be sent as audio out from one of the back line outs or headphones A or B? is it possible to be done? thank you As far as i know, you could select 1-8 in the "monitoring" section, with rotary know all the way to "IN" and then you should be able to listen to those sources with the headphones. I think output channels are intended to be controlled by software.
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
Important Information:
The vMix Forums uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
