vMix Forums
»
General
»
General Discussion
»
Squeezing out performance from an underpowered system
Rank: Newbie
Groups: Registered
Joined: 6/13/2022(UTC)
Posts: 1
|
Hi!
I'm using vMix with Core i7-10510U processor, 8GB ram, and just using the onboard graphics.
I had a 3 camera setup and it ran fine. One USB camera and two NDI/PTZ cameras. I just got two more NDI cameras, and render time increased significantly.
I found that with 4 cameras it's ok (render time around 20ms), but as soon as I add a 5th it goes up to 70+.
It doesn't matter which camera I remove, it's fine with 4 but not with 5.
All 4 cameras are running 1080p30, and the webcam says 1080p29.97.
Are there any recommendations on how to eek out a little more performance so I can run all 5 cameras?
Thanks
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 12/24/2021(UTC) Posts: 342  Location: athens Thanks: 113 times
Was thanked: 52 time(s) in 49 post(s)
|
You cant do magic but try to run one or more camera at 720p
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 3/7/2012(UTC) Posts: 2,602  Location: Canada Thanks: 33 times
Was thanked: 501 time(s) in 470 post(s)
|
@ likewut
Reduce the number of NDI and USB3 Camera Inputs and add a supported Capture Card (HDMI or SDI) to your system as that will help to ease the load on your CPU.
I would also recommend lowering your project settings to 720p (or lower).
Ice
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 4/23/2017(UTC) Posts: 1,143 Location: Germany Thanks: 3 times
Was thanked: 166 time(s) in 148 post(s)
|
First NDI is calculation power heavy. 4 NDI cams can also have an impact on the network. Check that all the data is travelling fine.
Keep in mind that a smaller bandwidth does mean higher compression and thus higher utilization for decompression in vmix.
That said the logic steps are
#1 Increase NDI bandwidth but keep an eye on the network
#2 Make sure only vmix is processing the NDI. Apps like the studio monitor consume resources as well
#3 lower the resolution if that is possible.
#4 Close other tasks to free some cycles
#5 Check other computer resources to identify bottlenecks in your system
#6 Add a proper GPU. This is extra money but will have the most impact. NVIDIA is well supported.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 7/1/2015(UTC) Posts: 1,150  Location: Houston TX Thanks: 319 times
Was thanked: 263 time(s) in 233 post(s)
|
Originally Posted by: mavik  First NDI is calculation power heavy. 4 NDI cams can also have an impact on the network. Check that all the data is travelling fine.
Keep in mind that a smaller bandwidth does mean higher compression and thus higher utilization for decompression in vmix.
That said the logic steps are
#1 Increase NDI bandwidth but keep an eye on the network
#2 Make sure only vmix is processing the NDI. Apps like the studio monitor consume resources as well
#3 lower the resolution if that is possible.
#4 Close other tasks to free some cycles
#5 Check other computer resources to identify bottlenecks in your system
#6 Add a proper GPU. This is extra money but will have the most impact. NVIDIA is well supported. All good advice. I would add that I've done more than what you describe with a much older system. (i7-5775C, 16GB RAM, GTX750 Ti, SSD)
|
|
|
|
|
|
vMix Forums
»
General
»
General Discussion
»
Squeezing out performance from an underpowered system
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
Important Information:
The vMix Forums uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
