vMix Forums
»
General
»
Feature Requests
»
Straight Line and Measured Angles in Telestrator
Rank: Newbie
Groups: Registered
Joined: 4/25/2025(UTC) Posts: 5  Thanks: 12 times
|
Currently the line tool in telestrator is a free-form line. 1) I'd like the ability to draw a traditional straight line between two points. Much like the square or circle drawing tools, I should click to set one end and then drag to set the end point. 2) I'd like the ability to measure an angle by providing three points. The first point is the beginning of a straight line, the second point is the end of the line (which completes Side 1) and the beginning of the angle to be measured. The third point is the end of the Side 2 line. Here's an example from a mobile app with these capabilities: 
|
|
|
|
|
|
Rank: Newbie
Groups: Registered
Joined: 1/11/2019(UTC) Posts: 3  Location: Chilliwack
|
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 12/14/2018(UTC) Posts: 149   Location: Clermont-Ferrand Thanks: 33 times
Was thanked: 9 time(s) in 8 post(s)
|
That's a very specific request, I might be wrong, but I'm not sure it would be useful to a large number of users.
|
|
|
|
|
|
Rank: Newbie
Groups: Registered
Joined: 4/25/2025(UTC) Posts: 5 Thanks: 12 times
|
Originally Posted by: MickeyMJJ  That's a very specific request, I might be wrong, but I'm not sure it would be useful to a large number of users. The second part with measured angles certain is. However, the primary request is drawing a straight line from two points which I think would be a pretty basic feature of a telestrator.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 12/14/2018(UTC) Posts: 149 Location: Clermont-Ferrand Thanks: 33 times
Was thanked: 9 time(s) in 8 post(s)
|
Originally Posted by: cgroom Originally Posted by: MickeyMJJ That's a very specific request, I might be wrong, but I'm not sure it would be useful to a large number of users. The second part with measured angles certain is. However, the primary request is drawing a straight line from two points which I think would be a pretty basic feature of a telestrator. Indeed, it wasn't clear; I had the angles in mind. ;)
|
|
|
|
|
|
Rank: Newbie
Groups: Registered
Joined: 1/11/2019(UTC) Posts: 3 Location: Chilliwack
|
The straight lines feature would be great for streaming billiards as well. I would not mind the angles for the overhead view but I'd like to be able to toggle it off and on as the angles wouldn't make sense on some camera shots where the table is skewed
|
|
|
|
|
|
Rank: Advanced Member
Groups: Registered
Joined: 12/27/2012(UTC) Posts: 5,474  Location: Belgium Thanks: 313 times
Was thanked: 1013 time(s) in 832 post(s)
|
trait lines i could use too (instant replay use)
|
|
|
|
|
|
vMix Forums
»
General
»
Feature Requests
»
Straight Line and Measured Angles in Telestrator
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
Important Information:
The vMix Forums uses cookies. By continuing to browse this site, you are agreeing to our use of cookies.
More Details
Close
